Version 2 (after Collaboration Review)Originally from the complete version (http://drupal.star.bnl.gov/STAR/blog/yipkin/2012/apr/26/paper-q-a) which includes implementation of a lot of obvious text corrections and here only those related to "Physics" are included : Flemming Videbaek : > - Is there a reason that 'transverse' is not in the title of the paper?
"Transverse single spin" comes up at the first sentence in the abstract. We would not like to change the title now.
> line 168. I suggest you introduce East and West here rather than later. Also I think downstream is
> ill defined in a collider enviroment.
A few persons/groups have made suggestions to this sentence. Now it's changed to be: "The Roman Pot stations are located on either side of the STAR interaction point (IP) at 55.5 m and 58.5 m with horizontal and vertical insertions of detectors respectively." > line 197 -- I am a little surprised that the signal spreads over up to 5 strips (500microns). Is that
> reasonable? Do you have a explanation. Also why not give the S:N values.
The text just indicates that the set of thresholds are used mostly to deal with the clusters with a length of 3-5 strips.
Concerning your comment on the five strip signal spread, most proton hits involve less, one and two are normal and most common. A hit of two strips is charge sharing between neighboring strips.
There is a simple explanation which is due to delta rays from the dE/dx process.
Otherwise, there is also non-negligible electronic coupling between adjacent strips. We saw that already during pp2pp days, very large signals had (energy deposits) caused activity in neighboring channels.
Protons can also disintegrate, for example at the entrance window or inside the silicon itself. in some cases this can still lead to a valid hit in case the secondary particles are in the forward direction very close to the original proton's momentum and no veto occurs.
> line 225. Is the beam p really know to this accuracy?
The fractional error is in the order of 1E-4 is. We change it to 100.2 GeV/c (instead of 100.22 GeV/c).
> Fig 6. Suggest to add in caption that error is stat+syst (as far I can tell).
Added a sentence "All error bars shown include both statistical and systematic errors." at the end of the caption.
Andrzej Sandacz:
> B) line 211 and Eqs (7), (8), (9) > L^{eff}, and also L^{eff}_x, L^{eff}_y are not defined explicitely. > One can try to infer which elements of the transport matrix may correspond to L^{eff} by guessing that > they must be the largest values, but still distiction between L^{eff}_x and L^{eff}_y is not > straightforward. The problem arised after replacing Eq. (7) written formerly for the general case in > terms of symbols, by the present selected example with values of the transport matrix elements for > a particular store. I understand the aim of the change: to give idea about values of TM elements. > But for an average reader these precise values probably are only of moderate interest. Thus I would > propose to go back to the previous version, i.e. general Eq. (7) with symbols, which is more transparent. Now, we have the transport matrix in both symbols and in real nos. and so L^{eff}_x and L^{eff}_y are clearly defined.
Hal for the Argonne group :
> ** l.168 - maybe change "downstream" -> "away from"??
A few persons/groups have made suggestions to this sentence. Now it's changed to be: "The Roman Pot stations are located on either side of the STAR interaction point (IP) at 55.5 m and 58.5 m with horizontal and vertical insertions of detectors respectively."
> ** l.225 - "... with p = 100.22 GeV/c the beam momentum." or something like this to explain why p is not 100.00.
Actually, even the total energy is not 100.00 GeV. All of these come from the fact that G-gamma has been set to be 191.5 between 191 and 192 (to avoid integers which might result in resonance). We've changed it to be "p = 100.2 GeV/c" as have the fraction error in the order about 1e-4.
> ** Eq. 11 - this equation assumes perfectly transversely polarized beams. We believe it is possible that due to > non-ideal beam orbits and magnetic fields or magnet alignments, the beams may have a small longitudinal > component at the STAR IR even when the rotators are off. This could lead to a (A_LS = A_SL)sin(phi) term in the > equation. It will (probably) also be negligible in your analysis as you describe ~ line 241. Please consider whether > you wish to add such a term in the equation and a couple words in the text about it. Alternately, you might > mention that higher order correction terms are ignored in the equation.
We now mention "higher order correction terms are ignored" under Equation 11, as you suggest.
> ** l.272 - perhaps quote the actual values instead of "~55" and "~10"??
The "collinearity" in reality is slightly different from run to run, not just one single value.
> ** l.283 - do we understand correctly that there may be a false asymmetry that is proportional to the beam polarization, and it has not been ruled out by your tests?
There we try to explain in detail that the false asymmetry is ~ 0.
> ** Fig.6 - The text and error bar run into each other for (d). > Fig.6 caption - is the vertical dashed line the average of experimental values or just zero or ...?? > Please include in the caption.
We've added "The vertical dashed line indicates where Im($r_5$)=0." at the end of the Fig. 6 caption.
> ** l.299,300 - this sentence is a bit confusing. You use "variable" for both deltaB and Re r_5, we believe. Maybe > something like "The remaining lines show changes of Re r_5 and Im r_5 when the parameter was varied by +/- 1 > sigma during the fit procedure." We are not sure this is even what is meant. Sorry.
Actually, you've understood perfectly. We've made the changes as you've suggested.
> ** l.308,9 - "... more emphasized in estimating ..." we are confused by this and aren't sure what the > authors are trying to say.
It just says the AN peak is more sensitive to Im(r5) and thus attracts more attention. This explains why we look at the Im(r5)'s in Fig. 6.
In the caption of Fig. 1, I now add "Positive y is pointing towards the sky and positive x is pointing to the center of the RHIC ring." > 144. At very high energy sqrt(s) - -> At high centre of mass energy, sqrt(s), Now, we define "center of mass energy" for sqrt(s) in "Introduction" (the 1st time that it appears, line 127) and here, we just say "At very high sqrt(s)". > 154-155. The contribution of the two spin-flip amplitudes, …., to the asymmetry AN is small as indicated by both experimental estimates [] and th. pred.[18] OK. We have changed it to : "The contribution of the two double spin-flip hadronic amplitudes, …., to the asymmetry AN is small, as indicated by both th. pred.[18] and experimental estimates [19,20]".
A few persons/groups have made suggestions to this sentence. Now it's changed to be: "The Roman Pot stations are located on either side of the STAR interaction point (IP) at 55.5 m and 58.5 m with horizontal and vertical insertions of detectors respectively." > 190. Give also value of the distance of 10 mm in units of the beam width at RPs. It's about 10-12 sigma's but it's probably difficult to be exact. > 214. small correction less than 4 $\mu$rad, the full - -> small, less than 4 $\mu$rad, correction, the full We've adopted Hal's suggestion : "small corrections of less than 4 $\mu$rad" . > 218-221. are not very clear, especially the use of “similar’ or “typical” We've changed to "are taken from the fits to data performed for each data segment. An example is shown in Fig.~2." > 257. the position of the t = 0 trajectory … - -> the position of the t = 0 elastically scattered proton trajectory or the beam position "t = 0 trajectory" is an ideal trajectory with no scattering. > 268-269. The simulation included … optics - -> Simulation of the elastically scattered proton transport through the The present form seems cleaner and the acceptance is mentioned in the following sentence. > 274-275. Assuming the background is unpolarized - -> Assuming that the background is the beam polarization "unpolarized" is probably easier to understand.
>298-302. Table II shows the fitted values of Re r5 and Im r5 together with statistical and total systematic A few people have commented/suggested, we've changed to: "In Table II, we show the central value of the fit and uncertainties on Re$\:r_5$ and Im$\:r_5$ due to various effects. In the first line of the table, the statistical error to the fit with the central value of the parameters is shown. The remaining lines show changes of Re$\:r_5$ and Im$\:r_5$, when the parameter was varied by $\pm$1$\:\sigma$ during the fit procedure. ......" > 308-309 Remove sentence: Since the maximum... since it is not needed This sentence explains why we look at Im(r5), but not Re(r5). > Present the main result with bold face font It's difficult to say which nos. are more important in this table. ( And we have changed 1st two lines into one line as Andrzej has suggested. ) > Table II. …. Measurement induced uncertainties (1) – statistical, …. (4). Uncertainties associated with the fit: (5) – the total cross-section … Changed to "Table II: ..... (1): Statistical Uncertainties. (2)-(4): Systematic uncertainties associated with this measurement. Steven Heppelmann for Penn State U. : >If I look for an issue it would be the rather large chi-square value on Figure 3b (32.68 for 17 DOF). This is fairly unlikely >Because the statistical error from the fits are only about 1/2 of the error on polarization, I don't think the story would
If we look at the variation of point-to-point, it's bigger than statistical variations. That means there
> 1)In line 214,215, "full transport matrix was used", does this mean Eq(8),Eq(9) and L_{x,y}^{eff} are not used for > the calculation of angles? If so, how to understand the uncertainties of L^{eff} in line 257,263,274 and in table II? > Or they are only used in estimating the uncertainties?
L^{eff} (for x or y) are just two of the elements (the two > 20 m) in the transport matrix and so when the transport matrix was used, they were indeed used. These were the two dominating terms in the transport matrix and the other elements are very small compared to L^{eff}. Conceptually, it's often easier to just consider these two terms when you try to understand various things in the analysis. So, equations (8) and (9) are just approximations to help people understand/grasp the main idea and the transport matrix has been used in the analysis. And indeed, the uncertainties L^{eff} are essentially the uncertainties of the transport.
> 3) Line 241: "preliminary results of this experiment [20] show that..." > Are these results not part of this analysis or not further checked using the > final data sample? It is a bit surprising to cite preliminary results of ourselves > for the same analysis, as we are the same collaboration or group.
The double-spin asymmetries A_NN/A_SS indeed belong to another set of analysis. Unlike the single-spin asymmetry (A_N) in this paper, there is NO square-root formula for extracting A_NN/A_SS. The square-root formula helps cancel out a lot of luminositybunch variance etc. We therefore need reliable normalization (bunch intensities etc.) for the A_NN/A_SS analysis which is an ongoing effort. We'd like to publish the A_N and r5 results first.
> 4) In line 305, "Re r_5 =0.00167 +/- 0.0063 in line 306 Im r_5=0.00722+/-0.057", > The rounding of the digits should be consistent and make real sense as in other places > in the paper.
What we've done is to show 3 significant figures for the measurements and 2-significant figures for the errors. A "typical" (but not always) rule for displaying experimental uncertainties is to show 1-significant figure less since the uncertainty is an estimate and cannot be more precise than the best estimate of the measured value. For some errors are too small compared to the dominant one (polarization), so we've also restricted the significance to 4 decimal points which is ~O(1%) of relative accuracy.
> line 171 : only -> almost exclusively Done ! > line 172 : insensitive -> nearly insensitive Done !
Last edited by Kin (May 9, 2012)
|